How To Solder Pins to Your Raspberry Pi Pico

The Raspberry Pi Pico is a smart little controller board to use along with your electronics initiatives. However, it doesn’t include any pins hooked up to its 40 GPIO pin holes. Without pins, the board can’t attach to motors, lighting, sensors or any of the opposite stuff you’d want to do a venture. In order to get any sensible use out of the Raspberry Pi Pico, you’ll want to solder pins to it. More complicated customers can solder unmarried wires at once to the holes or use feminine pin headers, however right here we’ll display you ways to connect an entire set of male pins, the commonest and helpful setup.

Soldering is an very important maker talent and the Raspberry Pi Pico supplies a good chance to be informed this talent. The Raspberry Pi Pico has 40 GPIO pins which want to be soldered so as to use the board. In this information, we’ll display you ways to solder those pins so the Pico is in a position to be used in all of your initiatives, together with our different tutorials.

If you may have by no means soldered prior to, then the $4 Raspberry Pi Pico is a a laugh board to get began with. It is a simple board to solder and it hasn’t were given any cramped areas or huge solder joints.

The key to soldering safely is preparation. Get your workspace setup prior to you flip the soldering iron on. Sit down and check that the entirety is to hand. Can you succeed in the solder? Do you may have the entire apparatus? Do you may have eye coverage and air flow?
Soldering is excellent a laugh, and you’re going to get the dangle of it, take your time and revel in your self.

(Image credit score: Tom’s Hardware)

For this venture you’re going to want:

  • Strip of 40 Male header pins
  • Side cutters / snips
  • Half / complete dimension breadboard
  • Soldering iron and stand
  • Solder
  • Eye coverage is very best apply, in particular when you don’t put on glasses

1. Ensure your workspace is obvious. Place the soldering iron in its stand after which position the stand inside of simple succeed in of your “soldering hand”. Wet your cleansing sponge, or be sure a brass tip cleaner is close by. Turn at the soldering iron and let it warmth up. If you may have any type of fume extraction, flip it on now. If now not keep in mind to solder close to an open window.

2. Take a strip of male header pins and rely the selection of pins. A standard strip may have 40 pins. Split the pins the usage of the facet cutters / snips in order that there are two strips of 20. Take care and double test prior to making the reduce. 


(Image credit score: Tom’s Hardware)

3. Fit the two strips to the Raspberry Pi Pico, in order that the shortest legs cross in the course of the holes at the board. The CPU of the Pico will have to be dealing with up, and the lengthy pins dealing with down. Alternatively you’ll turn the Pico over in order that the CPU is dealing with the breadboard. This will display the GPIO pin names, helpful if you’re not sure as to what each and every pin does.

4. Ensure the lengthy pins are at a 90 level attitude to the Raspberry Pi Pico and insert them into the breadboard. Check that the entire pins are seated appropriately and the entirety is instantly. 


(Image credit score: Tom’s Hardware)

5. Ensure you might be dressed in eye coverage prior to transferring on. Carefully take away the soldering iron from the stand, and “tin” the tip with just a little solder. Wipe the solder onto the cleansing sponge / brass tip cleaner to make sure that the end is blank and in a position to be used.

6. Bring the end of the soldering iron to the one nook pin of the Raspberry Pi Pico. Gently warmth the pin and the brass “hollow” across the pin. Gently feed in just a little solder in order that it melts and joins the pin to the brass. Remove the iron and wipe the surplus at the sponge / brass cleaner. Place the soldering iron again in its stand. 


(Image credit score: Tom’s Hardware)

7. Check your soldering! Take an in depth take a look at the joint. Is there excellent touch? Does it glance proper? Sometimes we would possibly want to reheat a joint, then waft just a little extra solder to be certain that a excellent connection. 


(Image credit score: Tom’s Hardware)

9. Solder the remainder pins, looking at the directions in steps 6 and 7. When executed flip off your soldering iron and let it calm down. 


(Image credit score: Tom’s Hardware)

If you soldered with the lengthy a part of the pins dealing with upward, it will have to seem like this: 


(Image credit score: Tom’s Hardware)


(Image credit score: Tom’s Hardware)

You at the moment are in a position to transfer on to one of tutorials akin to studying how to setup MicroPython, Basic Inputs and Outputs, or Robotics with Raspberry Pi Pico.